Mar 31, 2025 Leave a message

What Is Monel 400 And Alloy 400?

What is Monel 400 and alloy 400?

 

Monel Alloy 400
UNS N04400
Other common names: Alloy 400
W.Nr.2.4360, 2.4361
ASTM: B164, B564, B127, B165, B725, B730
ASME: SB164, SB564, SB127, SB165, SB725, SB730
QQ-N-281
Mil-T-1368
EN10204 3.1

What is Monel 400 and alloy 400?What is Monel 400 and alloy 400?

Monel 400 is a nickel-copper alloy (approximately 67% nickel - 23% copper) that resists high-temperature seawater and steam as well as salt and corrosive solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy has good corrosion resistance, good weldability, and high strength. Low corrosion rates in fast-moving salt or seawater, excellent resistance to stress corrosion cracking in most freshwaters, and resistance to a wide range of corrosive conditions make it widely used in marine applications and other non-oxidizing chloride solutions.

Monel Alloy 400
This nickel alloy is particularly resistant to hydrochloric and hydrofluoric acids when outgassed. As expected from its high copper content, Alloy 400 is rapidly attacked by nitric acid and ammonia systems.

Monel 400 has excellent mechanical properties at subzero temperatures and can be used up to 1000° F. It has a melting point of 2370-2460° F. However, Alloy 400 has low strength in the annealed condition, so various tempering methods can be used to increase strength.

What forms of Monel 400 does Gnee Steel offer?
Plates
Plates
Bars
Tubes (welded and seamless)
Fittings
Elbows, tees, stub ends, return pipes, caps, crossheads, reducers, unions, etc.
Wires
What are the characteristics of Monel 400?
Resistant to high-temperature seawater and steam
Resistant to fast-moving brackish or seawater
Resistant to stress corrosion cracking in most freshwaters
Particularly resistant to degassed hydrochloric and hydrofluoric acids
Somewhat resistant to hydrochloric and sulfuric acids at moderate temperatures and concentrations, but rarely the material of choice for these acids
Resistant to neutral and alkaline salts
Resistant to stress corrosion cracking caused by chlorides
Good mechanical properties from sub-zero temperatures to 1020°F
Strong resistance to alkalis

Chemical Composition, %

C Mn S Si Ni Cu Fe

.30 max

2.00 max

.024 max

.50 max

63.0 min

28.0-34.0

2.50 max

 

Corrosion Resistant Monel 400

Alloy 400 is virtually immune to chloride-ion stress corrosion cracking in typical environments. Generally, its corrosion resistance is very good in reducing environments but poor in oxidizing conditions. It is not suitable for oxidizing acids, such as nitric and nitrous acids. Nevertheless, it resists most alkalis, salts, water, foods, organic materials, and atmospheric conditions at normal and elevated temperatures.

This nickel alloy is attacked by sour gases above about 700° F, and molten sulfur attacks the alloy above about 500° F.

The corrosion resistance of Monel 400 is about the same as nickel, but the maximum working pressure and temperature are higher, and the cost is lower due to its excellent processing capabilities.

What applications is Monel 400 used for?
Marine Engineering
Chemical and Hydrocarbon Processing Equipment
Gasoline and Fresh Water Tanks
Crude Oil Stills
Degassing Heaters
Boiler Feedwater Heaters and Other Heat Exchangers
Valves, Pumps, Shafts, Fittings, and Fasteners
Industrial Heat Exchangers
Chlorinated Solvents
Crude Oil Stills

Send Inquiry

whatsapp

Phone

E-mail

Inquiry