Nov 28, 2024 Leave a message

Datasheet-For-Inconel-601-1-6-(1)-(1).pdf

nickel alloy UNS N06601 vs nickel-molybdenum-chromium alloy UNS N10276: Key Differences

What Are nickel alloy UNS N06601 and nickel-molybdenum-chromium alloy UNS N10276?

nickel alloy UNS N06601 is a nickel-chromium-iron solid-solution alloy (UNS N06601) strengthened in high-temperature service by aluminum and titanium additions that promote a protective oxide scale. nickel-molybdenum-chromium alloy UNS N10276 is a nickel-molybdenum-chromium alloy (UNS N10276) with tungsten, iron and cobalt, characterized by very low carbon and silicon. The short answer to the comparison: 601 is built for hot, oxidizing atmospheres, while C276 is built for wet, corrosive chemicals.

Chemical Composition at a Glance

nickel alloy UNS N06601 nominally contains 58–63% nickel, 21–25% chromium, iron as balance, with about 1.0–1.7% aluminum and small titanium additions; the chromium and aluminum are what give it oxidation resistance. nickel-molybdenum-chromium alloy UNS N10276 contains a nickel balance with 15.0–17.0% molybdenum, 14.5–16.5% chromium, 3.0–4.5% tungsten and 4.0–7.0% iron; the molybdenum and tungsten provide resistance to reducing acids and localized attack. Because the two alloys answer to different standards, confirm the governing specification (for example ASTM B166 for 601 sheet/plate, ASTM B575 for C276) before ordering.

High-Temperature Performance

nickel alloy UNS N06601 is one of the strongest choices for sustained high-temperature service in air, combustion gases and carburizing atmospheres. Lightly loaded parts can operate continuously well above 1,000°C, and the alloy resists oxidation and carburization where many stainless steels fail within weeks. nickel-molybdenum-chromium alloy UNS N10276, by contrast, is not intended for long-term high-temperature structural duty; its strengths are corrosion properties, and continuous chemical-process service is commonly limited to about 750°F (400°C). Where both high temperature and aggressive media meet, application-specific testing is required rather than a blanket substitution.

Corrosion Resistance

nickel-molybdenum-chromium alloy UNS N10276 resists pitting, crevice corrosion and stress-corrosion cracking in chloride media, and it handles sulfuric, hydrochloric and phosphoric acids in both oxidizing and reducing conditions, making it a standard choice for chemical reactors, scrubbers and waste-treatment equipment. nickel alloy UNS N06601 provides good resistance to aqueous corrosion in mildly aggressive media and excellent high-temperature corrosion resistance, but it is not equivalent to C276 in hot acids and chloride-rich chemical service.

Application Areas

nickel alloy UNS N06601 is specified for furnace components, radiant tubes, thermocouple sheaths, heat-treatment baskets, jet engine combustion hardware and other lightly loaded parts operating at high temperature. nickel-molybdenum-chromium alloy UNS N10276 is specified for chemical processing vessels, flue-gas desulfurization systems, pulp and paper equipment, industrial and municipal waste treatment, and marine systems handling harsh chlorides. Selection should follow the dominant failure mode: oxide scale and carburization point to 601, pitting and stress-corrosion cracking point to C276.

Frequently Asked Questions

What is the maximum operating temperature of nickel alloy UNS N06601? In oxidizing atmospheres, lightly loaded nickel alloy UNS N06601 parts can operate continuously well above 1,000°C (commonly cited to about 1,150–1,200°C), depending on load, atmosphere and section thickness. Confirm the limit for the specific furnace condition before design.

Can nickel-molybdenum-chromium alloy UNS N10276 be used at high temperature? It has some heat resistance, but C276 is not recommended for sustained high-temperature structural service; continuous chemical-process service is commonly limited to about 750°F (400°C).

Can nickel-molybdenum-chromium alloy UNS N10276 replace nickel alloy UNS N06601 in furnace parts? No. Furnace parts rely on 601's oxidation and carburization resistance above 1,000°C, where C276 offers no advantage and lower high-temperature capability.

Which alloy resists hydrochloric acid better? nickel-molybdenum-chromium alloy UNS N10276. Its molybdenum and tungsten content provides far better resistance to reducing acids and chloride-induced pitting than nickel alloy UNS N06601.

Are nickel alloy UNS N06601 and nickel-molybdenum-chromium alloy UNS N10276 weldable? Both are weldable with appropriate filler metals and controlled procedures. 601 is commonly welded with nickel-chromium filler such as ENiCrFe-3 or matching ERNiCr-3 type consumables; C276 is welded with matching ERNiCrMo-4 filler while keeping interpass temperatures low to preserve corrosion resistance.

Is nickel alloy UNS N06601 magnetic? Like most nickel-chromium alloys, nickel alloy UNS N06601 is essentially non-magnetic, which is useful in instrument housings and electrical applications.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry