Nov 26, 2025 Leave a message

astm-b444-(1)-(1).pdf

Inconel 600 Bars versus Inconel 625 Round Bars: Grade Selection Guide

Composition and Phase Structure

Nickel-chromium-iron bar and nickel-chromium-molybdenum-niobium bar are not interchangeable, and the difference starts at the melt. Grade UNS N06600 is a solid-solution nickel-chromium-iron alloy with no deliberate molybdenum or niobium addition; it relies on a stable austenitic matrix plus a chromium-rich surface oxide for its performance. Grade UNS N06625 is a nickel-chromium-molybdenum alloy strengthened by niobium and tantalum in solid solution, with molybdenum and niobium providing the pitting and crevice corrosion resistance that N06600 does not have.

Element (wt %) UNS N06600 (ASTM B166) UNS N06625 (ASTM B446) Effect
Nickel 72.0 min 58.0 min Austenitic matrix, chloride stress corrosion resistance
Chromium 14.0-17.0 20.0-23.0 Oxidation and scaling resistance
Iron 6.0-10.0 5.0 max Matrix element in N06600, residual in N06625
Molybdenum Not specified 8.0-10.0 Pitting and crevice corrosion resistance
Niobium plus tantalum Not specified 3.15-4.15 Solid-solution strengthening, creep resistance
Carbon 0.15 max 0.10 max Carbide formation, sensitisation risk

The practical consequence is a strength difference that survives any heat treatment. In the annealed condition ASTM B444 lists a minimum tensile strength of 827 MPa and a minimum yield strength of 414 MPa for N06625 Grade 1 tube, while annealed N06600 bar under ASTM B166 is specified at a minimum tensile strength of 550 MPa and a minimum yield strength of 240 MPa. A designer cannot close the gap by heat treating N06600, because the difference comes from alloy content rather than from condition.

High-Temperature Behaviour

Both grades resist oxidation, but they resist creep differently. N06625 holds useful stress-rupture strength to about 815 °C because the molybdenum and niobium slow diffusion in the matrix. N06600 is stable in continuous service to roughly 1095 °C in oxidising atmospheres where mechanical load is modest, and it is widely used for furnace internals, radiant tubes and thermocouple protection sheaths where thermal cycling rather than stress rupture governs. The two conditions are different questions: a designer choosing by oxidation resistance alone will over-specify or under-specify depending on the load path.

Both grades are also subject to a common limitation worth stating plainly. In the 540 to 760 °C range, prolonged exposure can precipitate carbides at grain boundaries and reduce ductility. Neither alloy should be selected on the assumption that high nickel content makes it immune to embrittlement, and the service temperature history must be reviewed rather than judged from the maximum temperature alone.

Corrosion and Chloride Stress Corrosion Cracking

In chloride-bearing water, N06600 is effectively immune to chloride stress corrosion cracking at practical stress levels and is the traditional choice for caustic evaporator tubes, where it also resists caustic cracking. N06625 goes further in aggressive halide environments: its molybdenum content raises resistance to pitting and crevice attack, and its higher chromium raises the critical temperature for localised corrosion. In seawater and in chloride-contaminated process streams with oxidising species, N06625 therefore has a clear advantage. Where the medium is caustic or high-purity water with low chloride, that advantage disappears and the cheaper grade performs identically.

Machining, Welding and Forming

N06600 machines with conventional carbide tooling at low surface speed and heavy feed, and it welds readily by gas tungsten arc and shielded metal arc processes without a post-weld heat treatment in most section sizes. N06625 is significantly stronger and more prone to work hardening, so it demands rigid setups, positive feeds and frequent tool changes to avoid a hardened surface layer; welding also requires controlled heat input because the niobium-rich weld pool is sluggish and susceptible to microfissuring if dilution or interpass temperature is not controlled. Bar stock in N06625 is commonly supplied in the annealed condition for subsequent machining, and forging is governed by ASTM B564.

Selecting Between the Two Grades

The decision rule is straightforward. Choose N06600 bar for furnace hardware, heat treating fixtures, caustic service and general high-temperature components where the stress level is moderate and the environment is oxidising. Choose N06625 bar for marine fasteners, seawater-exposed valve and pump internals, sour service components, and any application where localised corrosion or high mechanical load at temperature governs. When the requirement is a combination of high strength, halide resistance and moderate cost sensitivity, an intermediate nickel-iron-chromium grade is often reviewed as a third option.

Frequently Asked Questions

Q: Is N06625 bar always better than N06600 bar?
A: No. It is stronger and more resistant to localised corrosion, but it costs more and is harder to machine. In caustic service or in low-chloride oxidising atmospheres the extra alloy content adds no service life.

Q: Can N06600 and N06625 be welded to each other?
A: Yes, with a nickel-chromium filler metal selected for the higher-alloy side and a procedure qualified under ASME BPVC Section IX. Dissimilar joints should be qualified on the actual thickness and pass sequence used in production.

Q: Which grade resists chloride stress corrosion cracking better?
A: Both are highly resistant compared with austenitic stainless steel. N06625 adds pitting and crevice corrosion resistance because of its molybdenum and niobium content, which matters when chlorides are combined with oxidising species.

Q: Does either grade require post-weld heat treatment?
A: In most bar and tube thicknesses neither grade requires post-weld heat treatment. Where the service involves a sensitising temperature range or a corrosive medium, the requirement should be specified and verified rather than assumed.

Q: What bar form tolerances apply?
A: Straightness, diameter tolerance and surface finish are specified in the ordering standard, for example ASTM B166 for N06600 bar and ASTM B446 for N06625 bar, together with the required condition such as annealed, hot finished or cold drawn.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry