Corrosion-resistant ASTM B166 Nickel Alloy 600 round bar

Corrosion-resistant ASTM B166 Nickel Alloy 600 round bar
ASTM B166 Nickel Alloy 600 Bar (UNS N06600) is a nickel-chromium-iron alloy bar with excellent resistance to a wide range of corrosive media, including acid and chloride-ion stress corrosion cracking, making it suitable for use in high-temperature applications from cryogenic temperatures to approximately 2000°F (1093°C). The high nickel content provides resistance to reducing agents and organic and inorganic compounds, while the chromium content provides excellent oxidation resistance and high-temperature strength. Alloy 600 bar's combination of high strength, good fabrication properties, and heat and corrosion resistance makes it commonly used in chemical processing, nuclear engineering, and furnace components.
What is the ASTM standard for Inconel 600 rod?
Inconel 600 round bar is composed of 72% nickel, 14% chromium, iron, carbon, manganese, sulfur, silicon, and copper. This material has a high melting point of 1413°C. The minimum yield strength of ASTM B166 UNS N06600 round bar is 310 MPa, and the minimum tensile strength is 655 MPa.

Chemical Composition (ASTM B166 / UNS N06600):
| Element | Limit (wt %) | Element | Limit (wt %) |
|---|---|---|---|
| Nickel (Ni) | 72.0 min | Carbon (C) | 0.15 max |
| Chromium (Cr) | 14.0 – 17.0 | Manganese (Mn) | 1.0 max |
| Iron (Fe) | 6.0 – 10.0 | Sulfur (S) | 0.015 max |
| Silicon (Si) | 0.50 max | Copper (Cu) | 0.50 max |
Note: Alloy 600 contains no intentional molybdenum addition. Composition limits above follow the UNS N06600 registration; always verify against the current ASTM B166 edition before acceptance.
Physical and Mechanical Properties (Annealed Condition):
| Property | Typical Value |
|---|---|
| Density | 8.47 g/cm³ |
| Melting range | 1354 – 1413 °C (2470 – 2580 °F) |
| Tensile strength (annealed) | 550 – 690 MPa (80 – 100 ksi) |
| Yield strength, 0.2% offset (annealed) | 240 – 345 MPa (35 – 50 ksi) |
| Elongation (annealed) | 30 – 55% |
| Magnetic response | Non-magnetic in the annealed condition |
The values above are typical annealed ranges; minimum requirements for a specific diameter and temper are stated in the ASTM B166 data tables and should be confirmed with the mill test certificate (EN 10204 3.1).
Corrosion Resistance
- Chloride stress-corrosion cracking (SCC): Alloy 600 offers markedly better resistance to chloride SCC than austenitic stainless steels, which is why it is used in seawater and chloride-bearing process streams.
- Oxidation: the chromium content gives good resistance to high-temperature oxidation and to exhaust-gas and furnace atmospheres.
- Reducing media: the high nickel content provides good resistance to reducing acids, caustic solutions and most organic acids and compounds.
- Limitations: service in strongly oxidizing environments (e.g. hot concentrated nitric acid, wet chlorine) is restricted; Alloy 600 should not be used where intergranular attack in sensitized conditions is a known risk - review the specific medium with the mill.
Heat Treatment and Workability
Heat Treatment
Alloy 600 is not age-hardenable; cold working is the only practical hardening mechanism. Annealing (softening) begins at approximately 871 °C (1600 °F) and is effectively complete after holding at 927–982 °C (1700–1800 °F) for 10–15 minutes. Cooling rate has no effect on the annealed result, so the material may be water-quenched or air-cooled. For parts requiring full softening, hold at 1038 °C (1900 °F) briefly to dissolve any partially formed carbides.
Hot Working/Forging
Hot forming is typically performed in the range 1093–1232 °C (2000–2250 °F), with the finishing temperature kept above ~927 °C (1700 °F). Heavy deformation below roughly 871 °C (1600 °F) should be avoided because ductility falls in the intermediate temperature range, which can cause cracking during forging. Use a low-sulfur reducing furnace atmosphere to avoid sulfur embrittlement.
Cold Working
Alloy 600 work-hardens readily. Cold working (drawing, rolling, swaging) can be applied at room temperature to raise strength; subsequent annealing restores ductility. The high strength achieved by cold working is retained up to service temperatures where annealing effects begin (~427 °C / 800 °F).
Typical Applications
- Chemical processing equipment - vessels, piping, heat exchangers, caustic-handling plant.
- Nuclear engineering - steam-generator tubing and reactor internals where SCC resistance is critical.
- Furnace and heat-treatment components - retorts, muffles, baskets and fixtures operating above 650 °C.
- Aerospace and industrial fasteners, shafts and structural parts requiring oxidation resistance.
Available Bar Forms and Buying Checklist
| Form | Typical Supply Range (mill capability) |
|---|---|
| Round bar | 3 mm – 800 mm diameter |
| Square bar | 4 – 100 mm |
| Flat bar | 2 – 100 mm thick × 10 – 500 mm wide |
| Rectangles / hollow bar | 33 × 30 mm to 295 × 1066 mm; hollow 32 × 16 mm to 250 × 200 mm (OD × ID) |
| Finish | Cold drawn, centreless ground, hot rolled, smooth turned, peeled, polished |
| Tolerance | H8 – H13 / K9 – K12 or per client drawing |
- Confirm the governing standard: ASTM B166 (bar) - not B446, which applies to alloy 718 (UNS N07718).
- Request the mill test certificate showing Ni ≥ 72%, Cr 14–17% and S ≤ 0.015%.
- Specify temper (annealed / cold-drawn), surface finish and dimensional tolerance class.
- For nuclear or pressure applications, confirm ASME SB166 compliance and any supplementary NDE (UT) requirements.

Gnee Steel specializes in the production and sale of various nickel-based alloys, including Nickel 201, Nickel 202, Hastelloy C-276, Hastelloy C-22, Hastelloy B, Hastelloy C-4, Inconel Alloy 600, Inconel 625, Inconel 718, Inconel X-750, Incoloy Alloy 800, Incoloy 800H/HT, Incoloy 825, Monel Alloy 400, Monel K500, and high-temperature alloys. Gnee Steel's products are widely used in aerospace, chemical, electric power, automotive, and nuclear energy applications, and we can provide customized alloy solutions tailored to customer needs. For alloy pricing inquiries or customized alloy solutions, please contact us for a quote at ss@gneemetal.com.
FAQ:
What ASTM standard covers Alloy 600 round bar?
ASTM B166 (and ASME SB166). ASTM B446 applies to alloy 718 (UNS N07718), not to Alloy 600.
Is Alloy 600 precipitation-hardenable?
No. Alloy 600 cannot be strengthened by age hardening; only cold working raises its strength, and annealing restores softness.
What is the maximum service temperature of Alloy 600?
The alloy is suitable for continuous service up to approximately 1093 °C (2000 °F) in oxidizing atmospheres, subject to the specific environment and load.





