What Makes UNS N10276 the Benchmark for Severe Service?
UNS N10276, commercially known as nickel-molybdenum-chromium alloy UNS N10276, is a low-carbon nickel-chromium-molybdenum-tungsten alloy whose defining characteristic is a near-perfect balance of corrosion resistance across both oxidizing and reducing media. Carbon is held below 0.01% and silicon below 0.08%, and with a solution-annealed condition the material has a single-phase, face-centered cubic microstructure. It resists wet chlorine, hypochlorite, chlorine dioxide, sulfuric, hydrochloric, and phosphoric acids, and mixed acid systems such as nitric plus hydrofluoric acid. Molybdenum (15-17%) and tungsten (3-4.5%) provide a pitting resistance equivalent number of roughly 45, giving strong resistance to pitting and crevice corrosion in chlorides. The caveat is thermal history: the alloy delivers its full performance only in the solution-annealed and quenched condition, so welding or improper heat treatment can sensitize it and require a post-fabrication anneal.
Critical Applications and Why Bar Form Is Specified
C-276 bar is specified for high-stress, corrosion-critical components where failure would have serious safety, environmental, or production consequences. Typical parts include valve stems, gates, and trim in severe-service control, ball, and gate valves; high-strength fasteners, studs, and threaded rods for reactors, heat exchangers, and flanged systems; pump and compressor shafts, impeller hubs, and wear rings in service with mixed acids, chlorinated solvents, or seawater; agitator and mixer shafts in chemical and pharmaceutical reactors; and thermowells, probe sheaths, and sensor housings inserted into process streams. The solid bar form guarantees isotropic strength and uniform corrosion resistance across the cross-section, with no welds, seams, or grain-structure variations that could act as initiation sites for corrosion or fatigue failure.
Welding and Post-Weld Heat Treatment Protocols
Fabrication of C-276 follows one principle: preserve the solution-annealed, single-phase microstructure. GTAW (TIG) is strongly preferred for root and critical passes; SMAW and GMAW are acceptable with qualified procedures. Matching filler metal ERNiCrMo-4 per AWS A5.14 is standard. Use low heat input and hold the maximum interpass temperature at 125°C (257°F) to minimize time in the sensitization range of approximately 550-1150°C. Full argon shielding with 100% back purging is mandatory to prevent root oxidation and chromium depletion. For any component in corrosive service, a full post-weld solution anneal at 1065-1121°C (1950-2050°F), held about one hour per inch of thickness and followed by a rapid water quench, is strongly recommended and often code-required; it dissolves secondary phases such as mu phase and carbides formed in the heat-affected zone. As-welded use is acceptable only in non-corrosive or mildly corrosive duty and only with corrosion-test qualification.
Essential Quality Documentation and Supplementary Testing
Procuring C-276 bar for critical service requires more than a certificate of compliance. The mill test report must state the heat number, full chemical analysis verifying low carbon and silicon, actual tensile, yield, elongation, and hardness values, and the metallurgical condition, which must be solution annealed for corrosion service. Full traceability from finished bar back to the melt must be documented. Supplementary testing is commonly written into the purchase order: the intergranular corrosion test per ASTM G28 Method A on sensitized samples, with a low corrosion rate verifying proper annealing; pitting corrosion testing per ASTM G48 Method A (ferric chloride) at 40°C or 50°C for chloride service; and non-destructive examination such as full-body ultrasonic testing for large-diameter or rotating bars and liquid penetrant testing for machined or ground surfaces. For pressure-vessel components, material is supplied to ASME SB-574 with the applicable code marking.
C-276 vs C-22: How to Choose
C-276 and C-22 (UNS N06022) are close relatives, and the choice is technical and economic. Choose C-276 when the environment is well characterized and falls within its proven envelope of reducing acids, mild to moderate oxidants, and chlorides; its long service history and lower cost make it the economical workhorse for most severe corrosive services. Its lower chromium content, roughly 16% versus 22% in C-22, makes it somewhat less resistant to strongly oxidizing chlorides such as hot ferric or cupric chloride and more vulnerable at the extremes of chloride concentration and temperature. Choose C-22 when the environment is highly oxidizing, chloride-rich, or hard to characterize, because its higher PREN gives a greater safety margin against localized corrosion. A scrubber handling sulfuric acid with occasional chlorine ingress is likely served cost-effectively by C-276; a reactor processing hot mixed nitric/hydrofluoric acid with high chloride impurities justifies the premium of C-22.
Frequently Asked Questions
What is the UNS designation for nickel-molybdenum-chromium alloy UNS N10276? nickel-molybdenum-chromium alloy UNS N10276 is UNS N10276, a nickel-chromium-molybdenum-tungsten alloy supplied as bar under ASTM B574 and ASME SB-574.
Which filler metal is used to weld C-276? Matching filler metal ERNiCrMo-4 per AWS A5.14 is standard for GTAW, SMAW, and GMAW welding of C-276.
Is post-weld heat treatment required for C-276? For corrosive service, a full solution anneal at 1065-1121°C with rapid water quench is strongly recommended and often code-required to restore corrosion resistance.
What is the key corrosion test for C-276 bar? The ASTM G28 Method A intergranular corrosion test on sensitized samples is the most important quality test, verifying proper annealing and thermal stability.
How does C-276 differ from C-22? C-22 has higher chromium (about 22% vs 16%), giving better resistance to strongly oxidizing chlorides at a cost premium; C-276 covers most reducing and moderate oxidizing service at lower cost.
What documentation is mandatory for critical-service C-276 bar? mill test report with heat number, full chemistry, mechanical properties, and the solution-annealed condition statement, plus full melt traceability.





