Overview of Alloy 718 and Alloy X-750
Alloy 718 (UNS N07718) and Alloy X-750 (UNS N07750, commonly written as 750) are precipitation-hardening nickel-based alloys that share a nickel-chromium base but were developed for different service profiles. Alloy 718 is a nickel-chromium-iron alloy hardened by niobium, molybdenum, titanium and aluminium. It offers very high strength, good weldability and strong resistance to stress-corrosion cracking. Alloy X-750 is a nickel-chromium alloy that relies mainly on titanium and aluminium for precipitation hardening, and it is specified where long-term exposure to high temperature, rather than corrosion, is the limiting design condition.
Both grades are supplied as bar, wire, plate, sheet, strip, seamless tube, pipe, flange and forging, and both are ordered against nickel alloy specifications rather than stainless steel specifications. The practical differences only appear when a component has to survive either a corrosive aqueous environment at moderate temperature or a hot gas environment under sustained stress.
Chemical Composition Comparison
| Element | Alloy 718 | Alloy X-750 |
|---|---|---|
| Nickel (Ni) | 50-55% | 70% min |
| Chromium (Cr) | 17-21% | 14-17% |
| Iron (Fe) | Balance | 5-9% |
| Molybdenum (Mo) | 2.8-3.3% | - |
| Niobium (Nb) | 4.75-5.5% | - |
| Titanium (Ti) | 0.65-1.15% | 2.25-2.75% |
| Aluminium (Al) | 0.2-0.8% | 0.4-1.0% |
| Cobalt (Co) | 1.0% max | 1.0% max |
The table reflects the two hardening routes. Niobium and molybdenum in Alloy 718 form the strengthening phases and also raise resistance to pitting and crevice attack. Alloy X-750 replaces niobium and molybdenum with roughly three times the titanium and a higher aluminium level, and its nickel minimum of 70% provides a more stable austenitic matrix for prolonged high-temperature service. Neither grade relies on cobalt for strengthening.
Mechanical Properties at Room Temperature
| Property | Alloy 718 | Alloy X-750 |
|---|---|---|
| Tensile strength | 1370 MPa | 1100 MPa |
| Yield strength | 1030 MPa | 780 MPa |
| Elongation | 12-15% | 15-20% |
| Hardness (Rockwell) | B95-C36 | B88-C32 |
| Strengthening route | Niobium-bearing precipitation hardening | Titanium and aluminium precipitation hardening |
Alloy 718 delivers roughly 25% higher tensile strength and about 30% higher yield strength than Alloy X-750 in the hardened condition. The trade-off is ductility: Alloy X-750 shows 15-20% elongation against 12-15% for Alloy 718, so it tolerates more cold forming before cracking. Machinability follows the same pattern. Alloy 718, with its lower hardness ceiling and better chip formation, is usually the easier of the two to turn and mill, while Alloy X-750 work-hardens quickly and needs lower cutting speeds, sharper tooling and more rigid setups.
High-Temperature Performance, Creep and Corrosion Resistance
Alloy 718 is designed for moderate to high-temperature service but begins to lose mechanical properties above about 700 °C, which is why it is normally limited to that ceiling when strength retention governs. Its weldability makes it suitable for fabricated assemblies such as engine ducting, exhaust components and precision hardware. Alloy X-750 withstands higher temperatures, up to about 980 °C, with excellent creep resistance, that is, the ability to resist slow deformation under sustained load at temperature. That combination suits turbine blades, nuclear reactor springs and fasteners that stay hot for years.
In corrosion terms the ranking reverses. Alloy 718 resists pitting, crevice corrosion and stress-corrosion cracking more effectively, especially in aqueous and acidic environments, which is why it is a preferred choice for offshore oil and gas hardware. Alloy X-750 provides excellent resistance to oxidation and scaling at high temperature but is less effective than Alloy 718 against chemical attack in wet conditions.
Applications and Selection Guidance
Alloy 718 advantages: highest mechanical strength, excellent weldability, superior resistance to pitting and stress-corrosion cracking.
Alloy X-750 advantages: better high-temperature capability, excellent creep resistance, well suited to long-term high-heat exposure.
Alloy 718 applications: oil and gas wellhead and subsea components, aerospace structures and engine hardware, high-performance motorsport engines, high-strength fasteners.
Alloy X-750 applications: jet engine components, gas turbine seals and springs, nuclear reactor springs, heat-treatment fixtures and retaining rings.
On cost, Alloy 718 tends to be the more expensive grade because of its niobium and molybdenum content and the strong demand from oil and gas, aerospace and offshore engineering. Alloy X-750 is generally more affordable: it uses lower levels of expensive elements and relies on aluminium and titanium for hardening. Choose Alloy 718 when the duty is high stress plus corrosive exposure at moderate temperature. Choose Alloy X-750 when the duty is extreme temperature under long-term load, such as turbines, nuclear components or high-temperature springs.
Frequently Asked Questions
Q: Is Alloy 750 the same as Alloy X-750?
Yes. 750 is simply the short form of X-750, and both refer to the same precipitation-hardening nickel-chromium grade with UNS number N07750.
Q: Which grade is stronger at room temperature?
Alloy 718. Its tensile strength of about 1370 MPa and yield strength of about 1030 MPa exceed the roughly 1100 MPa and 780 MPa of Alloy X-750 in the hardened condition.
Q: Which grade performs better above 700 °C?
Alloy X-750. It retains useful strength and creep resistance up to about 980 °C, while Alloy 718 begins to lose mechanical properties above roughly 700 °C.
Q: Is Alloy 718 or Alloy X-750 easier to weld?
Alloy 718 is considerably easier to weld and is routinely used for welded fabrications. Alloy X-750 is less weldable and needs tighter control of heat input and post-weld treatment.
Q: Which grade resists corrosion better?
Alloy 718. Its niobium and molybdenum additions give better resistance to pitting, crevice corrosion and stress-corrosion cracking in aqueous and acidic service.
Q: Which grade is more cost-effective?
Alloy X-750 is usually the more affordable option because it avoids expensive molybdenum and niobium additions, provided that its lower corrosion resistance still meets the duty.





