Apr 09, 2024 Leave a message

Which Materials Are Stronger Than Nickel-Chromium Superalloys?

Why "Stronger" Is Not One Single Number

Buyers who ask which metal outperforms a nickel-chromium superalloy usually mean one of four different things, and each one points to a different material. Ultimate tensile strength, or UTS, is the maximum load a specimen carries before it breaks. Yield strength at 0.2 percent offset is the load at which a component begins to deform permanently. Creep and stress-rupture strength describe how long a part survives a constant load at temperature. Specific strength, meaning UTS divided by density, describes how much load a structure carries for its own mass. A grade that wins on one measure can lose on another, so the comparison below keeps the four measures separate instead of averaging them.

Material (UNS / grade) Typical UTS Density Specific strength Practical continuous service limit
Titanium Grade 5, Ti-6Al-4V (UNS R56400) 895-1,000 MPa 4.43 g/cm3 approx. 200 MPa per g/cm3 about 400 C
Titanium Grade 4 (UNS R50700) 550 MPa minimum 4.51 g/cm3 approx. 122 MPa per g/cm3 about 350 C
Nickel-chromium-iron, aged (UNS N07718) 1,240-1,370 MPa 8.19 g/cm3 approx. 159 MPa per g/cm3 about 700 C
Nickel-chromium-molybdenum (UNS N06625) 830-930 MPa 8.44 g/cm3 approx. 104 MPa per g/cm3 about 980 C
Nickel-chromium-cobalt (UNS N06617) 700-800 MPa 8.36 g/cm3 approx. 90 MPa per g/cm3 about 1,150 C
Nickel-chromium-iron, annealed (UNS N06600) 550 MPa minimum 8.47 g/cm3 approx. 65 MPa per g/cm3 about 980 C short term

The table shows the central trade-off. Titanium wins the specific-strength column by a wide margin, while the precipitation-hardened nickel grades win on absolute tensile and creep strength above roughly 500 C.

Titanium Alloys That Beat the Nickel-Chromium Family on Strength-to-Weight

Titanium is only about 54 percent as dense as a nickel-chromium alloy, so even a moderate tensile strength converts into a large mass saving. Grade 5 Ti-6Al-4V, the workhorse alpha-beta alloy, is specified under ASTM B265 for sheet, plate and strip and under ASTM B348 for bar and billet, and it reaches 895-1,000 MPa UTS with 828-895 MPa yield after standard heat treatment. Grade 4 commercially pure titanium, the strongest of the four unalloyed grades, is guaranteed at 550 MPa minimum UTS and 483 MPa minimum yield by ASTM B265.

Grade 5 Ti-6Al-4V: highest strength-to-weight ratio, aerospace structures, fasteners, pressure bottles.

Titanium Grade 4: strongest unalloyed grade, bone plates, offshore hardware, high-stress chemical parts.

Titanium Grade 2: the general-purpose grade, heat exchangers, marine fittings, chemical tanks.

Titanium Grade 1: lowest strength but highest ductility and lowest cost, liners and architectural trim.

Where titanium stops competing is temperature. Above about 400-500 C it oxidises rapidly and absorbs oxygen, nitrogen and hydrogen, which embrittles the surface and destroys ductility. Furnace and turbine hot-section parts therefore stay with the nickel-chromium family even though the titanium grade is stronger per kilogram at room temperature.

Standard Designations and Chemistry of the Nickel-Chromium Family

The nickel-chromium alloys used for high-temperature service are identified by UNS number and by Werkstoff number, which is the fastest way to compare a mill certificate with a purchase order. Chromium supplies oxidation resistance, molybdenum and niobium supply solid-solution and precipitation strengthening, and cobalt raises the creep limit.

Common designation UNS Werkstoff Nr. Key chemistry
Nickel-chromium-iron N06600 2.4816 Ni 72.0 min, Cr 14.0-17.0, Fe 6.0-10.0
Nickel-chromium-iron-aluminium N06601 2.4851 Ni 58.0-63.0, Cr 21.0-25.0, Al 1.0-1.7
Nickel-chromium-cobalt-molybdenum N06617 2.4663 Ni 44.5 min, Cr 20.0-24.0, Co 10.0-15.0, Mo 8.0-10.0
Nickel-chromium-molybdenum-niobium N06625 2.4856 Ni 58.0 min, Cr 20.0-23.0, Mo 8.0-10.0, Nb+Ta 3.15-4.15
Nickel-chromium-iron, low carbon N06690 2.4642 Ni 58.0 min, Cr 27.0-31.0, Fe 7.0-11.0
Nickel-chromium-iron, age hardened N07718 2.4668 Ni 50.0-55.0, Cr 17.0-21.0, Nb 4.75-5.50, Mo 2.80-3.30, Fe balance
Nickel-chromium-iron-titanium, age hardened N07750 2.4669 Ni 70.0 min, Cr 14.0-17.0, Ti 2.25-2.75, Al 0.40-1.00, Fe 5.0-9.0

Service Temperature Limits by Grade

Temperature capability decides which family can be used at all, so it should be checked before strength. The figures below assume an oxidising atmosphere such as air; in hydrogen-rich or other reducing atmospheres the usable limit drops because the protective chromium oxide film is no longer stable.

Grade Continuous service limit Short-term excursion
N06600 about 980 C about 1,090 C
N06625 about 980 C about 1,090 C
N07718 about 700 C long term about 870 C
N07750 about 700 C about 815 C
N06617 about 1,150 C about 1,180 C

Age-hardened grades such as N07718 and N07750 owe their strength to gamma-prime and gamma-double-prime precipitates. Those precipitates coarsen above roughly 700 C; once they coarsen, the alloy does not recover its original strength, which is why the long-term limit is written separately from the short-term excursion limit.

How to Choose Between the Two Families

Mass-critical structure below 400 C: titanium Grade 5 is normally the strongest practical option per kilogram.

Bolted joints, turbine discs and downhole tools at 500-700 C: aged nickel-chromium-iron grades give the highest absolute strength.

Furnace internals, radiant tubes and exhaust hardware at 900-1,150 C: only the solid-solution nickel-chromium grades survive, because creep and oxidation, not tensile strength, govern life.

Chloride or seawater exposure: titanium resists pitting and crevice attack without the molybdenum level needed in a nickel alloy.

Cost-sensitive work at moderate temperature: compare delivered cost per finished part, not cost per kilogram, because titanium machining and welding add significantly to the conversion cost.

Frequently Asked Questions

Q: Is titanium always stronger than a nickel-chromium superalloy?
No. Titanium alloys such as Grade 5 are stronger per unit mass, and their absolute tensile strength is higher than the annealed solid-solution nickel grades. The age-hardened grades N07718 and N07750 still exceed titanium in absolute tensile and yield strength at room temperature.

Q: Which single grade has the highest room-temperature tensile strength?
Among the materials compared here, aged N07718 is highest at roughly 1,240-1,370 MPa UTS. Titanium Grade 5 follows at roughly 895-1,000 MPa, although it delivers that strength at barely half the density.

Q: Why do nickel-chromium alloys cost more than titanium?
Nickel, cobalt and molybdenum are the expensive elements, and the vacuum melting routes used for aerospace and nuclear grades add further cost. Commercially pure titanium and alloy titanium are both usually cheaper per kilogram, while remaining more expensive to machine.

Q: Can titanium replace nickel-chromium parts in a furnace?
No. Titanium oxidises rapidly above about 500 C and absorbs interstitial elements, so it loses ductility. Furnace and combustor parts at 900-1,150 C require the oxide-forming nickel-chromium grades.

Q: Does the strongest grade also resist corrosion best?
No. N06625 combines high strength with outstanding resistance to chlorides and high-temperature gases, but N06690 offers better resistance to strongly caustic and high-purity water environments at lower strength.

Q: Which documents should be checked on delivery?
Verify the heat number, the UNS designation, the melting practice and the mechanical test results against the applicable ASTM or EN specification, and confirm the grain size where creep resistance is required.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry