Nickel-molybdenum-chromium alloys are a family of nickel-based corrosion-resistant materials made by alloying nickel with substantial amounts of molybdenum and chromium. They are selected when stainless steels and lower-alloy nickel grades cannot survive the process medium, and they are supplied in a range of grades whose composition is tuned to a specific set of corrosive and mechanical demands.
What This Alloy Family Is
Adding molybdenum to nickel produces strong resistance to reducing acids and to pitting and crevice attack, while chromium builds the passive surface film that resists oxidising conditions and high-temperature attack. Combining both elements in one alloy, together with tungsten and controlled carbon and silicon levels, produces materials that tolerate mixed acid streams and contaminated media rather than a single clean chemical.
This balance is what separates these grades from other nickel materials such as the nickel-iron-chromium alloys used for milder oxidising service. Because molybdenum also improves hot processability, the alloys can be hot worked, cold formed and welded with normal nickel-alloy practice, and they remain ductile and easy to fabricate into complex shapes.
Across the family, chromium ranges from about 1% to 25%, molybdenum from about 5% to 30% and iron from 0% to 30%, with nickel making up the balance. Additional elements such as tungsten, carbon, vanadium, titanium and niobium are added according to grade, and every composition is optimised for a specific set of properties.
How Is This Material Made?
Production starts with melting the charge in a hot liquid state so that the elements combine into a homogeneous alloy. Modern practice uses vacuum or electroslag melting for the more demanding grades in order to hold carbon, sulfur and gas contents at low levels, which is essential because these residuals control both corrosion resistance and hot workability.
After melting and mixing, the heat is cast into ingots or continuously cast blooms, then homogenised and worked down by forging, rolling or extrusion. Wrought product is finished with a solution anneal and a rapid quench to dissolve any second phases and to restore the uniform single-phase structure that gives the family its corrosion performance.
How the Grades Differ
| Grade | UNS number | Composition character | Typical duty |
|---|---|---|---|
| Alloy C-276 | N10276 | Ni with about 16% Mo, 15% Cr and 4% W | Mixed acids, chlorides, wet chlorine, flue-gas plant |
| Alloy C-22 | N06022 | Similar molybdenum level with higher chromium and tungsten | Strongly oxidising and reducing mixed-acid service |
| Alloy C-4 | N06455 | Ni-Mo-Cr with very low carbon and iron | Chemical plant where weld-zone stability is critical |
| Alloy B-2 | N10665 | Ni-Mo with essentially no chromium | Hydrochloric acid and other strongly reducing media |
| Alloy 625 | N06625 | Ni-Cr-Mo with niobium addition | High-strength parts, seawater and high-temperature service |
Chromium-bearing grades are the general-purpose choice because they tolerate both oxidising and reducing conditions. The nickel-molybdenum grades without chromium are more specialised: they excel in hydrochloric acid but must never be exposed to oxidising media, which is why the selection decision usually starts with the oxidising power of the process stream.
What These Alloys Are Used For
Because the grades are designed for moderately to severely corrosive environments where equipment life is critical, they appear in a consistent set of industries:
Chemical and petrochemical: pipe, valves, pumps, reactors, columns and heat exchangers handling acids, chlorides and solvents.
Nuclear and power: reactor vessels, waste-handling equipment and flue-gas desulphurisation components.
Pulp and paper: digesters, bleach plant equipment and recovery piping exposed to chlorides.
Oil and gas: sour-service piping, wellhead components and offshore equipment where chlorides and carbon dioxide are both present.
Pharmaceutical and fine chemical: vessels and piping that must stay clean, corrosion free and free of contamination.
Waste treatment: incineration, effluent neutralisation and disposal equipment.
Selection and Fabrication Notes
Define the medium first: oxidising, reducing or mixed, and note the chloride level, temperature and any entrained solids before choosing a grade.
Check the temperature ceiling for the specific medium, since attack rises steeply with temperature in acids such as sulfuric and phosphoric.
Assume rapid work hardening during forming, and plan interstage annealing for cold work involving large reductions.
Use matching nickel-base filler for welding, keep heat input low and clean the joint area, because residual carbon, sulfur and oxygen degrade corrosion resistance.
Apply a solution anneal after hot forming or heavy cold work so that the single-phase structure and the corrosion performance are restored.
Order against the relevant product specification and require a composition certificate and mechanical test report for each heat.
Frequently Asked Questions
Q: What is the difference between these alloys and stainless steel?
Stainless steel relies on chromium in an iron base and works well in oxidising conditions. These nickel-molybdenum-chromium alloys add high molybdenum in a nickel base, which greatly extends resistance to reducing acids and to chloride pitting, and they tolerate far more aggressive media.
Q: How is this material made?
The elements are melted together in a hot liquid state, refined to low carbon and gas levels, cast into ingots and then worked into bar, plate or tube followed by a solution anneal and rapid quench.
Q: What is this family used for?
Pipes and valves in the chemical and petrochemical industries, reactor vessels in the chemical and nuclear industries, pulp and paper equipment, offshore oil and gas hardware and waste-treatment plant.
Q: Which grade is the most widely used?
Alloy C-276, UNS N10276, is the most common general-purpose grade because its combination of molybdenum, chromium and tungsten suits mixed reducing and oxidising duty, including chloride-rich streams.
Q: How much chromium and molybdenum do these grades contain?
Across the family chromium runs from about 1% to 25%, molybdenum from about 5% to 30% and iron from 0% to 30%, with nickel as the balance and optional tungsten, carbon, vanadium and titanium additions depending on grade.
Q: Are these alloys easy to fabricate?
Yes. They are ductile, can be hot and cold formed, and weld readily with matching nickel-base filler. The main cautions are rapid work hardening during forming and the need to control heat input and cleanliness when welding.





