1. Supply Conditions of Ti-6Al-4V (Grade 5 Titanium Alloy)
Annealed (Recrystallization Annealed, O State)
This is the most widely used supply condition for GR.5. The annealing process typically involves heating the alloy to 700–760°C (1292–1400°F) for 1–4 hours, followed by air cooling or furnace cooling. For stress-relief annealing (a lower-temperature variant), the material is heated to 530–620°C (986–1148°F) and held before cooling, which primarily reduces residual stresses without significantly altering the base microstructure. The fully annealed state produces a homogeneous, equiaxed α + β microstructure with balanced ductility, toughness, and moderate strength.
Solution Annealed and Aged (STA, Solution Heat Treated + Precipitation Hardened)
This condition involves two key steps: first, heating the alloy to a temperature above the β-transus (typically 900–950°C/1652–1742°F, below the full β-phase region to retain some α-phase) and holding to form a uniform α + β matrix, followed by rapid quenching (water or air cooling) to create a supersaturated metastable β-phase (and martensitic α' phase in some cases). Second, aging at a lower temperature (480–550°C/896–1022°F) for 4–8 hours allows fine α-phase precipitates to form within the β-matrix. The STA process yields a bimodal or lamellar α + β microstructure, significantly boosting tensile and fatigue strength at the expense of slight reductions in ductility and fracture toughness.
β Annealed
Less common for general applications, β annealing entails heating GR.5 above its β-transus temperature (≈995°C/1823°F) and holding to fully convert the microstructure to β-phase, then cooling at a controlled rate (furnace cooling for slow cooling, air cooling for faster cooling). This produces a coarse lamellar (Widmanstätten) α + β structure, which enhances creep resistance and high-temperature stability but reduces room-temperature ductility and impact toughness. It is mainly used for components operating at elevated temperatures (up to 400°C/752°F) with low fatigue load requirements.As-Forged / As-Rolled (Mill Finish)
These are non-heat-treated supply states, retaining the microstructure formed during hot working (forging or rolling). The as-forged state typically has a deformed α + β structure with directional grain flow, offering high strength but lower uniformity in properties across the component. The as-rolled state (for sheets/plates) has a flattened, elongated α-phase microstructure with improved surface quality and consistent thickness, suitable for preliminary forming operations before final heat treatment.




2. Application Scenarios for Different Supply Conditions
Annealed Condition
Aerospace: Airframe structural components (wing ribs, fuselage frames, landing gear brackets), fasteners, and hydraulic system tubing. Its balanced ductility and toughness prevent brittle failure under dynamic flight loads, while its moderate strength meets airframe weight-saving requirements.
Medical Devices: Orthopedic implants (hip and knee prostheses, bone plates/screws) and dental implants. The annealed state's excellent biocompatibility, corrosion resistance (in bodily fluids), and ductility ensure implant longevity and reduce the risk of fracture during surgical implantation and long-term use.
Industrial: Chemical processing equipment (heat exchangers, valve bodies, piping) for corrosive media (chlorides, acids). The annealed microstructure's high corrosion resistance and ductility enable it to withstand cyclic thermal and chemical stresses without cracking.
Automotive: Exhaust system components (manifolds, turbocharger housings) and high-performance suspension parts, where it balances strength, heat resistance, and weight reduction.
Solution Annealed and Aged (STA) Condition
Aerospace: Critical engine components (turbine blades, compressor disks, connecting rods) and landing gear struts. The STA state's high tensile strength (up to 1100 MPa vs. 860 MPa for annealed) and fatigue resistance are critical for withstanding high centrifugal loads (in engines) and impact loads (in landing gear).
Defense: Armor plating, missile components, and firearm barrels. Its elevated strength and hardness provide ballistic protection and structural integrity under high-stress, high-impact scenarios.
High-Performance Industrial: Downhole oil and gas tools (drill collars, wellhead components) and aerospace fasteners. The STA condition's resistance to high-pressure, high-temperature (HPHT) environments and fatigue failure makes it ideal for deep-well drilling and critical structural connections.
β Annealed Condition
Aerospace: Engine casings and exhaust nozzles operating at 350–400°C (662–752°F), where creep resistance and dimensional stability at elevated temperatures are prioritized over room-temperature ductility.
Power Generation: Turbine components for geothermal power plants, where exposure to high-temperature, corrosive steam requires enhanced high-temperature performance.
As-Forged / As-Rolled Condition
Intermediate Manufacturing: Pre-formed blanks for custom-machined components (e.g., aerospace forgings, industrial valve bodies) that will undergo final heat treatment to achieve targeted properties. The as-rolled state is also used for sheet metal fabrication (bending, stamping) in preliminary production stages, as its work-hardened microstructure offers sufficient formability before annealing.
Low-Cost, Non-Critical Applications: Agricultural machinery parts and marine hardware, where strict property uniformity is not required, and cost savings from skipping heat treatment are prioritized.





