Monel 400 Plates, ASTM B127 UNS N04400 Plates
Monel 400 plates
Monel 400 Slab Stockist,Monel 400 Slab,Monel 400 Polished Plate,Monel 400 Gasket Stock,Monel 400 Plate Price in China,AMS 4544 Monel Alloy 400 Annealing Strip,Monel 400 Cold Rolled Plate Distributor in China,Monel 400 Coil Supplier in China.
Monel 400 is a binary alloy of nickel and copper (traces of iron, manganese, carbon and silicon). This alloy has high strength, resistance to acidic and alkaline environments, and good ductility and thermal conductivity. The Monel 400 is suitable for use in temperatures from minus to 1,000°F (538°C). It can only be hardened by cold working.
•UNS N04400
•ASTM B127
•AMS 4544
•BS 3072NA1
•BS 3076NA13
•QQ-N-281
•DIN 17750
Sheet: δ0.8-36mm; Width: 650-2000mm; Length 800-12000mm
Pipe: φ6-273mm; δ1-30 mm; Length 1000-8000mm
Rod: φ4-200mm; Length: 2000-6000mm
Strip: 0.05*5.0-5.0*250mm
Wire: 0.01-10mm
Monel 400 chemical composition of plates, sheets and rolls
| grade | C | manganese | silicon | trumpet | copper | iron | you |
|---|---|---|---|---|---|---|---|
| Monel 400 | Up to 0.30 | Up to 2.00 | Up to 0.50 | Up to 0.024 | 28.00 – 34.00 | Max 2.50 | 63.00 minutes |
Typical characteristics of the Monel 400
The table below covers the typical attributes of the Monel 400.
|
attribute |
metric system |
Inch |
|
density |
8.8 g/cm3 | 0.318 lb/in3 |
|
melting point |
1350° Celsius | 2460° Fahrenheit |
|
Expansion factor |
13.9µm / m. °C (20-100°C) |
7.710 times-6 inch/inch (70-212°F) |
|
Modulus of rigidity |
65.3 kN/mm2 |
9471 kg |
|
Elastic modulus |
105-120 kN / mm2 | 15230-17405 lbf |
Monel 400 Mechanical Properties of Sheets, Sheets and Rolls
| subassembly | density | melting point | tensile strength | Yield Strength (0.2% offset) | elongation |
|---|---|---|---|---|---|
| Monel 400 | 8.8 g/cm³ | 1350°C(2460°F) | Psi – 80,000,MPa – 550 | Pound force - 35,000, MPa - 240 | 40 % |
Thermal processing
Alloy 400 Plate is a relatively soft material that accepts thermoforming into almost any shape. The thermoforming temperature range is 1200 – 2150°F (649 – 1177°C). For high pressures, the recommended temperature range is 1700 – 2150°F (927 – 1177°C). Temperatures as low as 1200°F (649°C) may reduce brightness. Working at lower temperatures will result in higher mechanical properties and smaller grain sizes.
Equivalent grade of 400 Monel sheets
| standard | WERKSTOFF NR. | United Nations system | JIS | baccalaureate | gauss | Avonno | EN |
|---|---|---|---|---|---|---|---|
| Monel 400 | 2.4360 | N04400 | 4400 NW | NA 13 | МНЖМц28-2,5-1,5 | NU-30M | Nickel-copper-iron |
Applications for the Monel 400The
Monel 400 can generally be found in the following areas:
Marine Engineering,
Chemical Processing,
Hydrocarbon Processing, Heat
Exchangers,
Valves,
Water Pumps
