The question of whether 1.4529 is a superalloy comes up often, because the grade combines a high nickel content with excellent performance in aggressive service. The answer is that 1.4529 is not a superalloy. It is an iron-based, super-austenitic stainless steel designed for chloride-rich aqueous service, not a nickel- or cobalt-based alloy designed to carry load at 700 °C and above.
Is 1.4529 a Superalloy?
EN 1.4529 is the numeric designation of the grade X1NiCrMoCuN25-20-7, covered by the UNS number N08926. The matrix is austenitic iron with roughly 25 % nickel, from 19 % to 21 % chromium and 6 % to 7 % molybdenum. There is no gamma-prime precipitation hardening and no cobalt or refractory metal matrix, so the grade is not a superalloy in the accepted sense of the term.
What created the confusion is that its performance is high enough to be mistaken for one. In chloride-bearing water, in seawater and in many acids, 1.4529 outperforms ordinary austenitic stainless steels by a wide margin, and the cost is correspondingly higher. But the property that makes it valuable is electrochemical corrosion resistance in aqueous environments, not strength retention in hot gas.
A useful comparison is the difference between this grade and a genuine high-temperature alloy. A precipitation-hardening nickel-based alloy such as GH4169 derives its value from creep and fatigue strength at 600-700 °C. Grade 1.4529 derives its value from a passive film that resists breakdown by chloride ions at ambient and moderate temperature, and it should not be substituted for a high-temperature alloy in a highly stressed hot section.
The Single Most Important Characteristic
If one property has to be singled out, it is the grade's outstanding resistance to localised chloride attack, meaning pitting and crevice corrosion, supported by strong resistance to chloride stress corrosion cracking and to general corrosion in reducing acids.
That resistance is quantified by the pitting resistance equivalent number, PREN = Cr + 3.3 Mo + 16 N. With about 20 % chromium, 6.5 % molybdenum and 0.2 % nitrogen, grade 1.4529 reaches a PREN of approximately 44. For orientation, type 316L sits near 25, the 904L type near 34, standard duplex 2205 near 35 and super duplex 2507 in the range of 40 to 43. Only the highest-molybdenum austenitic and duplex grades and the nickel-chromium-molybdenum alloys exceed 1.4529 in this respect.
Three alloying additions produce that result. Molybdenum is the primary element that resists pitting and crevice corrosion in chlorides. Nitrogen raises pitting resistance, stabilises the austenite and increases strength. Copper improves resistance in sulphuric acid and suppresses corrosion in mixed acid service. The combination is what allows 1.4529 to be used with seawater and with chloride-containing process streams where 316L would pit within months.
Chemistry and Typical Properties
| Element or property | Value |
|---|---|
| Chromium | 19.0-21.0 % |
| Nickel | 24.0-26.0 % |
| Molybdenum | 6.0-7.0 % |
| Copper | 0.5-1.5 % |
| Nitrogen | 0.15-0.25 % |
| Carbon | 0.02 % maximum |
| Manganese, silicon | 2.0 % and 0.5 % maximum |
| Iron | Balance |
| Pitting resistance equivalent number | approximately 44 |
| Density | about 8.1 g/cm³ |
| Tensile strength | about 650-700 MPa |
| 0.2 % proof strength | about 300 MPa |
| Elongation | about 40 % |
| Magnetic behaviour | essentially non-magnetic in the solution-annealed condition |
Solution annealing is carried out at about 1,100-1,150 °C followed by rapid water quenching. The quench is essential: it keeps the molybdenum and chromium in solid solution and prevents the precipitation of intermetallic phases that would both reduce corrosion resistance and embrittle the material. Service exposure above roughly 500-600 °C should be avoided for the same reason.
Clearing Up a Common Identification Error
Much of the published information about grade 1.4529 mixes up three different materials, and the mix-up matters because the properties are not interchangeable.
EN 1.4529, UNS N08926 is the 6Mo super-austenitic stainless steel described here, with 19-21 % Cr, 24-26 % Ni, 6-7 % Mo, copper and nitrogen, used in seawater and chloride service.
EN 1.4539, UNS N08904 is the well-known 904L type, with about 20 % Cr, 25 % Ni, 4.5 % Mo and copper. It is a lower-molybdenum material with a PREN near 34, and it is not a substitute for 1.4529 in severe chloride duty.
EN 1.4835, UNS S30815 is a heat-resisting austenitic steel with about 21 % Cr, 11 % Ni, deliberate silicon and cerium additions and nitrogen. It is the grade that resists oxidation and cyclic oxidation up to roughly 1,150 °C through a self-healing chromia-silica scale, and it is the correct material for radiant tubes and similar high-temperature components.
The high-temperature story, with silicon and cerium building a protective oxide that survives thermal cycling, belongs to the 1.4835 type and not to 1.4529. Choosing 1.4529 for a 1,150 °C radiant tube application, or choosing a heat-resisting grade for a seawater heat exchanger, would both be mistakes.
Applications, Product Forms and Fabrication
Grade 1.4529 is supplied as plate, sheet, strip, bar, seamless tube, welded tube and forgings. Common order routes are ASTM A240 for plate, sheet and strip, EN 10088-2 and EN 10088-3 for European flat and long products, EN 10216-5 for seamless tube and NORSOK M-630 for offshore piping, where the 6 % molybdenum austenitic grades are grouped by their pitting resistance and qualified for seawater service.
Seawater systems: heat exchanger tubing, condenser tubing, pump bodies, valves and firewater piping.
Flue gas desulphurisation: absorber internals, spray headers, duct liners and mist eliminator components.
Pulp and paper: bleach plant washers, filtrate tanks and chlorine dioxide handling equipment.
Chemical and hydrometallurgical plant: sulphuric and phosphoric acid service, sulphate and chloride leach circuits, crystallisers and evaporators.
Offshore and marine: process piping and seawater cooling systems, where chloride levels rule out lower grades.
Fabrication follows austenitic stainless practice with a few additions. The grade can be hot formed between about 1,000 °C and 1,150 °C and cold formed with intermediate annealing, although it work-hardens quickly. Welding is routinely done by gas tungsten arc welding with a matching 6 % molybdenum filler or a nickel-chromium-molybdenum filler where higher weld-metal corrosion resistance is wanted. Low heat input, strictly controlled interpass temperature not exceeding about 150 °C and clean, oxide-free surfaces are the key requirements. Because the material is fully austenitic and chemically stable after quenching, no post-weld heat treatment is normally required.
Frequently Asked Questions
Q: Is 1.4529 a superalloy?
No. It is a super-austenitic stainless steel, designation X1NiCrMoCuN25-20-7 with UNS number N08926, based on an iron matrix with about 25 % nickel. It has no precipitation-hardening or high-temperature strengthening mechanism of the kind that defines a superalloy.
Q: What is the single most important characteristic of 1.4529?
Its resistance to pitting and crevice corrosion in chloride-bearing environments, with a pitting resistance equivalent number of about 44, combined with resistance to chloride stress corrosion cracking. That is what qualifies it for seawater and severe chloride process service.
Q: Is 1.4529 the same as the heat-resisting grade 1.4835?
No. They are different EN numbers. Grade 1.4835, UNS S30815, is an austenitic heat-resisting steel containing silicon and cerium, intended for oxidation resistance up to about 1,150 °C. Grade 1.4529 is intended for chloride corrosion resistance in water and process chemicals.
Q: Can 1.4529 be welded?
Yes. Gas tungsten arc welding with a matching 6 % molybdenum filler or a nickel-chromium-molybdenum filler is standard practice. Use low heat input, keep the interpass temperature below about 150 °C and clean the joint thoroughly before welding. Post-weld heat treatment is not normally needed.
Q: Is 1.4529 magnetic?
In the solution-annealed condition the structure is fully austenitic and essentially non-magnetic, with a very low relative permeability. Cold work can introduce a slight magnetic response.
Q: What is the maximum service temperature of 1.4529?
It is an aqueous corrosion grade rather than a heat-resisting grade, and continuous exposure above roughly 500-600 °C should be avoided because intermetallic precipitation reduces both corrosion resistance and toughness.





