Sep 04, 2025 Leave a message

nickel alloy UNS N07718 Bright Rod: Specifications and Applications

What Is an nickel alloy UNS N07718 Bright Rod?

An nickel alloy UNS N07718 bright rod is a bar of nickel alloy UNS N07718 (UNS N07718), a high-strength, precipitation-hardenable nickel-chromium alloy, supplied with a smooth, bright surface finish. The bright finish is achieved by cold drawing after hot rolling, a process that improves dimensional accuracy, refines the surface, and imparts a polished, blemish-free appearance that is valuable for machined components, fasteners, and precision parts. The alloy exhibits high tensile, yield, and creep-rupture strengths up to approximately 1300 degF (700 degC), combined with excellent corrosion and oxidation resistance, which is why it is a standard material for aerospace, gas turbines, chemical processing, power generation, and oil and gas equipment.

Chemical Composition (UNS N07718)

Element Content (%)
Nickel 50.0-55.0
Chromium 17.0-21.0
Molybdenum 2.8-3.3
Niobium plus tantalum 4.75-5.50
Titanium 0.65-1.15
Aluminum 0.20-0.80
Cobalt 1.0 max
Iron Balance
Carbon 0.08 max
Manganese 0.35 max
Silicon 0.35 max
Sulfur 0.015 max

Composition follows ASTM B637, the standard specification for hot-rolled and cold-worked nickel alloy UNS N07718 bars and forgings; verify the current edition for exact limits. The niobium, titanium, and aluminum additions are what make the alloy age-hardenable through precipitation of the gamma double-prime phase.

Mechanical Properties and Condition

Property Typical value
Density 8.2 g/cm3
Tensile strength (annealed) about 930 MPa (135,000 psi)
Yield strength, 0.2% offset (annealed) about 482 MPa (70,000 psi)
Elongation about 45%

The mechanical values above are typical for the annealed condition. nickel alloy UNS N07718 is normally used in the solution-treated-and-aged condition, where yield strength rises well above 1100 MPa with good ductility; guaranteed values depend on the condition, product form, and specification, so the required heat treatment must be stated when ordering.

Bar Sizes, Forms, and Finishes

nickel alloy UNS N07718 bars are available in round bar from about 3 mm to 800 mm diameter, hex bar from 2 to 100 mm across flats, flat bar with thickness 2-100 mm and width 10-500 mm, square bar 4-100 mm, hollow bar, billets, and rectangles. Finishes include cold (bright) drawn, centerless ground, hot rolled, smooth turned, peeled, polished, hairline, sand-blasted, and black. The bright-drawn finish is chosen when dimensional accuracy and surface quality reduce downstream machining or directly satisfy application requirements.

Oxidation Behavior and Applications

nickel alloy UNS N07718 oxidizes at a parabolic, diffusion-controlled rate over a wide temperature range, roughly 950-1300 degC in air, with oxidation intensifying sharply near the top of that range, where severe deformation can also occur. In service, the alloy is normally used at temperatures up to about 700 degC, where its aged strength is retained. Common applications include aerospace high-speed aircraft fuselage components and engine parts; power generation gas turbines and high-temperature equipment; chemical processing components in extreme environments; oil and gas downhole and subsea control equipment; and cryogenic storage components.

Frequently Asked Questions

What does bright mean in nickel alloy UNS N07718 bright rod? Bright refers to the surface finish produced by cold drawing after hot rolling, which improves dimensional accuracy and gives the bar a smooth, polished, bright appearance.

At what temperature does nickel alloy UNS N07718 oxidize? nickel alloy UNS N07718 oxidizes at a parabolic, diffusion-controlled rate over roughly 950-1300 degC in air; oxidation becomes extremely intense above about 1300 degC. For load-bearing service it is normally limited to about 700 degC.

What standard covers nickel alloy UNS N07718 bars? ASTM B637 covers hot-rolled and cold-worked nickel alloy UNS N07718 bars and forgings. Product forms and conditions should be specified against this standard.

Why is nickel alloy UNS N07718 strong at high temperature? It is precipitation-hardenable: solution treatment followed by aging precipitates the gamma double-prime phase, which blocks dislocation movement and provides high yield, tensile, and creep-rupture strength up to about 700 degC.

What is the melting range of nickel alloy UNS N07718? about 1260-1340 degC, depending on exact composition; consult the alloy data sheet for the precise value for a given heat.

Where is nickel alloy UNS N07718 bright bar used? In aerospace engine and airframe parts, gas turbine components, chemical processing equipment, oil and gas downhole and subsea equipment, and cryogenic storage components, wherever high strength, corrosion resistance, and dimensional precision are required.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry