nickel-iron-chromium alloy UNS N08800: A Versatile Nickel-Iron-Chromium Alloy
nickel-iron-chromium alloy UNS N08800 (UNS N08800) is a nickel-iron-chromium alloy containing 30-35% nickel, 19-23% chromium, and a minimum of 39.5% iron, with aluminum and titanium additions for high-temperature stability. It is widely used in the chemical industry, nuclear power generation, and industrial heating equipment, with typical applications including nitric acid coolers, acetic anhydride cracking tubes, heat exchange equipment, and heat exchanger tubes. Its combination of high chromium and sufficient nickel gives the alloy strong resistance to oxidation and carburization at elevated temperatures while remaining cost-effective compared with higher-nickel alloys.
Corrosion Resistance Profile
nickel-iron-chromium alloy UNS N08800 has excellent resistance to stress corrosion cracking in chloride environments, in low-concentration sodium hydroxide solutions, and in high-temperature high-pressure water, which is why it is used to manufacture equipment where stress corrosion cracking resistance is the governing requirement. Its resistance to stress corrosion cracking is better than that of general austenitic stainless steels such as 304 and 316, and in many chloride and caustic service environments it outperforms higher-nickel alternatives in economic terms. It is important to compare by environment rather than by blanket ranking: nickel alloy UNS N06600 offers superior resistance in reducing and halogen-rich media thanks to its much higher nickel content, while nickel-iron-chromium alloy UNS N08800 is the stronger choice in carburizing and sulfidizing high-temperature atmospheres thanks to its higher chromium content. For equipment exposed to chlorides, caustic solutions, or high-temperature water, nickel-iron-chromium alloy UNS N08800 is frequently selected over both nickel alloy UNS N06600 and copper-nickel alloy UNS N04400 for stress corrosion cracking resistance combined with moderate cost.
Hot Working
Hot working of nickel-iron-chromium alloy UNS N08800 is performed in the temperature range of approximately 950-1200 degC, with water quenching or rapid air cooling after the final hot operation. To obtain the best properties and creep resistance, a solution treatment must be carried out after hot processing. In practice the material can be charged directly into a furnace already heated to about 1200 degC, held for a sufficient time, discharged quickly, and hot worked within the specified range; if the material temperature drops below the working range it must be reheated before further deformation.
nickel-iron-chromium alloy UNS N08800 work-hardens at a rate greater than that of austenitic stainless steel, so forming equipment must be selected accordingly. Cold-worked material should be in the solution heat-treated condition, and intermediate annealing should be performed when the amount of cold work is large. As a general guideline, when cold working exceeds roughly 10% reduction, the workpiece should receive a secondary solution treatment to restore the annealed microstructure and corrosion resistance before further forming or final service.
Welding
nickel-iron-chromium alloy UNS N08800 can be welded by any of the conventional processes used for austenitic nickel alloys, including gas tungsten arc welding (GTAW/TIG), plasma arc welding, shielded metal arc welding (SMAW), gas metal arc welding (GMAW/MIG), and submerged arc welding, with matching nickel-based filler metals such as ERNiFeCr-1 or ERNiCr-3 families. Pulsed arc welding is often preferred for control of heat input. Joint surfaces must be clean and free of grease, oil, and marking compounds, and low heat input with proper interpass control is recommended to maintain the alloy's corrosion resistance and avoid excessive grain growth in the heat-affected zone. For filler metal selection and procedure qualification, follow the requirements of the applicable product and welding specifications.
Selection Notes
Choose nickel-iron-chromium alloy UNS N08800 for heat exchangers, furnace components, and chemical equipment where chloride stress corrosion cracking, caustic service, or high-temperature oxidation and carburization are the design drivers. When long-term creep strength above about 650 degC is required, consider the controlled variants nickel-iron-chromium alloy UNS N08810 (UNS N08810) and nickel-iron-chromium alloy UNS N08811 (UNS N08811), which carry the same base chemistry with tighter control and higher-temperature solution annealing. Confirm the applicable product form standard, such as ASTM B407 for seamless pipe and tube or B163 for heat exchanger tubes, when ordering.
Frequently Asked Questions
What is nickel-iron-chromium alloy UNS N08800 used for? It is used for nitric acid coolers, acetic anhydride cracking tubes, heat exchange equipment and tubes, furnace components, and equipment for chloride, caustic, and high-temperature water service in chemical and nuclear plants.
Is nickel-iron-chromium alloy UNS N08800 resistant to stress corrosion cracking? Yes. Its combination of nickel and chromium gives it excellent resistance to chloride stress corrosion cracking, low-concentration caustic solutions, and high-temperature high-pressure water, better than general austenitic stainless steels.
At what temperature is nickel-iron-chromium alloy UNS N08800 hot worked? The recommended hot working range is approximately 950-1200 degC, followed by water quenching or rapid air cooling and a solution treatment for best properties and creep resistance.
Is nickel-iron-chromium alloy UNS N08800 better than nickel alloy UNS N06600? It depends on the environment. nickel-iron-chromium alloy UNS N08800 has higher chromium, so it is better in carburizing, sulfidizing, and oxidizing high-temperature atmospheres and is lower in cost; nickel alloy UNS N06600's much higher nickel content makes it better in reducing and halogen-rich media.
How is nickel-iron-chromium alloy UNS N08800 welded? With conventional processes such as GTAW, plasma arc, SMAW, and GMAW using matching nickel-based filler metals, clean joint surfaces, and controlled heat input.
When should nickel-iron-chromium alloy UNS N08810 or 800HT be used instead? When the design temperature and stress require higher creep and stress-rupture strength, typically above about 650 degC. The H and HT variants control carbon, aluminum, and titanium and use higher solution annealing temperatures to develop a coarse grain structure.





