1. What Is 800H Alloy Seamless Pipe?
The 800H grade (UNS N08810) is a carbon-controlled nickel-iron-chromium alloy supplied as seamless pipe for components that must retain strength during long exposure at high temperature. Unlike a precipitation-hardened superalloy, it does not rely on a gamma prime reaction: its creep and rupture strength come from a coarse austenitic grain structure and from grain-boundary carbides. That combination makes it a workhorse material for furnace tubes, pyrolysis coils, heat-exchanger tubing and high-temperature process piping.
Two features distinguish it from the standard low-carbon version of the same alloy family. First, carbon is held in a narrow band of 0.05 to 0.10 %, high enough to form the carbides that pin grain boundaries but controlled enough to avoid excessive sensitisation. Second, a high-temperature anneal followed by rapid cooling produces a grain size of ASTM 5 or coarser, and coarse grains are exactly what raise creep resistance.
2. Composition and Microstructure
The chemistry is deliberately simple, and the absence of molybdenum, tungsten and vanadium is just as important as what is present:
| Element | Content, % | Role |
|---|---|---|
| Nickel | 30–35 | Austenitic matrix, thermal stability, resistance to scaling |
| Chromium | 19–23 | Oxidation and high-temperature corrosion resistance |
| Carbon | 0.05–0.10 | Forms grain-boundary carbides for creep strength |
| Aluminium | 0.15–0.60 | Oxide adherence and internal oxidation resistance |
| Titanium | 0.15–0.60 | Stabilises carbon, limits sensitisation |
| Manganese | 1.5 max | Deoxidation and structure control |
| Silicon | 1.0 max | Deoxidation, oxidation resistance |
| Sulphur | 0.015 max | Restricted to protect hot ductility |
| Iron | Balance | Matrix balance |
At service temperature the structure is a single-phase austenite with M23C6-type carbides decorating the grain boundaries. There is no precipitation-hardening phase, and no molybdenum or tungsten is present in the matrix, so strength must be developed through grain size, carbide distribution and the solid-solution hardening of nickel and chromium alone.
3. Solution Annealing and Temperature Capability
Solution anneal: approximately 1120–1170 °C, followed by rapid cooling - water quench or a fast air blast - so that carbon stays in solution and the structure is not sensitised.
Grain size: ASTM 5 or coarser is normally specified. A fine grain size is easier to achieve but gives noticeably lower creep resistance.
Continuous service: the grade is used in the roughly 600–1000 °C band, with pressure-part design codes generally limiting metal temperature to about 980 °C.
Short-term excursions: brief exposure above the continuous limit is possible in dry oxidising service, but each excursion consumes part of the creep life of the component.
Creep, not room-temperature tensile strength, controls design in this band. A pipe that is perfectly adequate at ambient temperature will deform slowly under sustained load at 900 °C if the stress exceeds the rupture allowance for the intended life.
4. What Determines the Cost per Kilogram
A per-kilogram figure depends far more on how the pipe is made and examined than on a single published number:
Nickel content: with 30–35 % nickel in the analysis, the metal cost tracks the nickel reference price much more closely than it tracks iron or chromium.
Melting and refining: carbon must be held in a narrow band, which calls for controlled melting and decarburisation practice rather than a generic heat.
Seamless conversion: piercing, hot rolling and cold drawing to final size consume yield and energy, and thicker walls and larger diameters raise the conversion cost disproportionately.
Solution annealing: a full-length anneal at around 1150 °C followed by a rapid quench adds furnace time, straightening and handling.
Testing and certification: dimensional tolerance, hydrostatic pressure testing, eddy-current or ultrasonic examination, grain-size measurement and third-party inspection all add to unit cost.
Order quantity and rolling schedule: small or non-standard sizes are produced in short runs and cost more per kilogram than stock sizes.
Two pipes of the same outside diameter can therefore differ substantially in unit cost when their wall tolerance, examination class or certification requirements differ, so a single figure quoted without those details is not a meaningful comparison.
5. How to Specify the Grade Correctly
Quote the specification that matches the product form: ASTM B407 or ASME SB-407 for pipe, ASTM B515 for welded tube, ASTM B409 for plate, sheet and strip, ASTM B408 for rod and bar, and ASTM B366 for fittings.
State the carbon range: the 0.05–0.10 % band is what separates this grade from the standard low-carbon version, and the difference is decisive where creep strength matters.
State the grain size: a requirement of ASTM 5 or coarser should appear on the order, because it cannot be verified from a chemical certificate alone.
Define the examination: pressure test, nondestructive examination method and acceptance level should be agreed before rolling, since they influence both cost and delivery.
Where a designer is unsure whether the standard low-carbon version of the family is adequate, the correct answer is dictated by temperature and design life rather than by price alone: the lower-carbon grade is not a substitute where sustained loads at high temperature must be carried.
6. Frequently Asked Questions
Q: What is the difference between the standard grade and 800H?
The 800H grade is the carbon-controlled, coarse-grain version of the nickel-iron-chromium family. Carbon is held at 0.05–0.10 % and the solution anneal produces a grain size of ASTM 5 or coarser, which together give markedly better creep and rupture strength.
Q: At what temperature can 800H seamless pipe be used continuously?
The grade is normally applied in the 600–1000 °C band. Pressure-part design codes generally cap metal temperature at about 980 °C, and the actual allowable stress falls steadily as temperature rises.
Q: Why is carbon controlled between 0.05 and 0.10 %?
Carbon is needed to form the grain-boundary carbides that resist creep, but too much carbon promotes sensitisation and reduces ductility. The narrow band is the compromise between the two effects.
Q: Does this grade contain molybdenum?
No. The alloy is essentially nickel, iron and chromium with controlled carbon, aluminium and titanium. It contains no deliberate molybdenum, tungsten or vanadium addition, and its high-temperature strength comes from microstructure rather than from heavy alloying.
Q: Why is a coarse grain size specified?
Grain boundaries are the weak path for creep at high temperature. A coarse grain structure reduces the boundary area available for sliding, which is why ASTM 5 or coarser is called out for this grade.
Q: Which specification applies to pipe of this grade?
ASTM B407, together with its ASME SB-407 equivalent, covers pipe in this grade. Welded tube, plate and bar are covered by other documents, so the specification quoted must match the product form being ordered.





