Silicon steel is the workhorse magnetic material of the transformer and electrical machinery industries. Two families dominate: non-grain-oriented electrical steel (NGOES, also written CRNGO) and grain-oriented electrical steel (GOES, also written CRGO). Their electromagnetic behaviour is not a single property but the outcome of three interacting groups of variables: alloying chemistry, microstructure, and the processing route used to make the sheet. Understanding how each group acts makes it far easier to match a grade to a specific transformer, motor or appliance design.
How Alloying Elements Shape Electromagnetic Properties
The chemical composition of silicon steel, and particularly the silicon and carbon contents, has a decisive effect on magnetic performance.
Silicon raises the electrical resistivity of the steel, which directly reduces eddy current loss. It also promotes ferrite grain coarsening, lowers coercivity and reduces crystal anisotropy, so magnetisation becomes easier and hysteresis loss falls. Under weak magnetic fields the high-silicon sheet shows strong magnetic inductance. The picture reverses at high field: because saturation induction itself falls, silicon reduces the maximum magnetic inductivity. The accepted rule of thumb is that saturation induction drops by about 500 Gauss for every 1% of silicon added.
Carbon is the undesirable element. It raises coercivity and hysteresis loss and reduces magnetic induction. If the carbon content of the finished sheet exceeds about 0.0296%, the preferred orientation is partially or completely destroyed during high-temperature annealing. This is why grain-oriented electrical steel is supplied with very low carbon, and why non-grain-oriented steel containing more than about 0.02% carbon cannot be used to produce high-grade products. Iron loss rises steadily as carbon content increases.
Microstructure Effects: Grain Size and Sheet Thickness
Grain size in the finished sheet is set by the annealing stage and is normally expressed as the number of grains per unit area. During production, if the grains grow too large, not all of the carbon can precipitate as carbides along the grain boundaries as intended, and some carbon remains dissolved in the ferrite as an interstitial solid solution. The practical consequence is that iron loss increases again once grain size passes an optimum.
Thickness acts on eddy current loss. The thinner the sheet, the smaller the eddy currents induced by alternating flux, and therefore the smaller the total core loss. As a result, silicon steel is produced in thin gauges matched to the operating frequency. There is a trade-off: as thickness falls from 0.5 mm to 0.2 mm the B25 value declines gradually, and below 0.10 to 0.05 mm the decline becomes steeper. The difference in B25 between 0.5 mm and 0.05 mm material is roughly 500 to 1100 Gauss.
Processing Route: Primary and Secondary Cold Rolling
Rolling practice strongly influences the microstructure that survives annealing, and therefore the final electromagnetic properties. Ordinary non-grain-oriented silicon steel is generally produced by a single primary cold rolling pass, while higher-grade non-grain-oriented steel is produced by secondary cold rolling with an intermediate anneal. Cold rolling enlarges the ferrite grains and reduces the total grain boundary area, so magnetic resistance is lower and hysteresis loss is smaller.
Selecting Between CRNGO and CRGO
The two families are not interchangeable. Grain-oriented steel is processed so that the easy magnetisation direction of the crystals aligns with the rolling direction. That gives very low loss along the rolling direction but strongly anisotropic behaviour, which suits wound cores, distribution transformers and large power transformers where the flux direction is fixed. Non-grain-oriented steel has far more uniform properties in all directions and is the standard choice for rotating machines, small transformers and household appliances, where flux paths turn through the core.
Frequently Asked Questions
Q: What does silicon do to the electromagnetic properties of steel?
Silicon raises resistivity and cuts eddy current loss, promotes ferrite grain coarsening, lowers coercivity and reduces crystal anisotropy. The trade-off is that saturation induction falls by roughly 500 Gauss for every 1% silicon.
Q: Why is carbon harmful in silicon steel?
Carbon increases coercivity and hysteresis loss and reduces magnetic induction. Above about 0.0296% in the finished sheet it partially or completely destroys the preferred orientation during high-temperature annealing.
Q: How does grain size affect iron loss?
Grains that are too large prevent carbon from precipitating along the grain boundaries, leaving carbon dissolved in the ferrite. Iron loss then rises instead of falling, so an optimum grain size exists.
Q: Why is silicon steel made in thin sheets?
Eddy current loss falls as sheet thickness decreases, so total core loss falls with it. Thickness is matched to the operating frequency, although the B25 value declines as the sheet becomes thinner.
Q: What is the difference between primary and secondary cold rolling?
Ordinary non-grain-oriented grades use a single primary cold rolling pass. High-grade grades use secondary cold rolling with an intermediate anneal, producing larger ferrite grains, fewer grain boundaries and lower hysteresis loss.
Q: How do CRNGO and CRGO differ in service?
CRGO has very low loss along the rolling direction but strong anisotropy, suiting wound cores and power transformers. CRNGO has more uniform properties in all directions and suits motors, small transformers and appliances.





