Dec 03, 2025 Leave a message

Cold and Hot Working Difficulty Of Titanium

1. Cold Working of Commercially Pure Titanium

1.1 Processing Difficulty

The cold working of CP Ti is characterized by moderate to high difficulty, which is mainly reflected in the following aspects:

Low room-temperature ductility and work hardening sensitivity: At room temperature, CP Ti has an HCP crystal structure with limited slip systems (only 3 independent slip systems), resulting in relatively poor plastic deformation ability compared to face-centered cubic (FCC) metals (e.g., aluminum alloy, austenitic stainless steel). Moreover, CP Ti has extremely high work hardening rate-its strength increases sharply with the increase of cold deformation degree. For example, after 20% cold rolling, the tensile strength of Grade 2 CP Ti can rise from the initial 345–415 MPa to over 550 MPa, while its elongation drops from 20–25% to less than 8%. This means that during continuous cold forming (such as deep drawing, bending), the material is prone to cracking if intermediate treatment is not performed.

High deformation resistance: CP Ti has high yield strength and flow stress at room temperature. For example, the yield strength of Grade 2 CP Ti is about 275–345 MPa, which is significantly higher than that of 6061-T6 aluminum alloy (about 240 MPa) and close to that of low-carbon steel (about 250–300 MPa). Higher forming loads are required during cold processing, which puts forward higher requirements for the rigidity and tonnage of forming equipment.

Surface quality sensitivity: CP Ti has high chemical activity at room temperature and is prone to forming a hard and brittle oxide film (TiO₂) on the surface. During cold deformation (such as drawing and rolling), the oxide film is easy to fall off and cause surface scratches or adhesion to the mold, affecting the surface finish of the workpiece. In addition, if the surface has defects (such as microcracks), stress concentration is easy to occur during cold processing, leading to the expansion of defects and even fracture of the workpiece.

1.2 Special Process Requirements

To overcome the above difficulties, the following special processes need to be adopted in the cold working of CP Ti:

Intermediate annealing treatment: When the cold deformation degree exceeds 15–20%, intermediate stress relief annealing or recrystallization annealing must be carried out to eliminate work hardening, restore the ductility of the material, and avoid cracking in subsequent processing. The annealing temperature is generally 600–700°C, and the holding time is 0.5–2 hours, with furnace cooling or air cooling to ensure the recrystallization of the material and the elimination of internal stress.

Mold and lubrication technology: The mold should be made of high-hardness and wear-resistant materials (such as cemented carbide or high-speed steel with surface coating), and the surface should be polished to reduce friction. At the same time, high-performance lubricants (such as molybdenum disulfide-based lubricants or special titanium processing oils) must be used to form a stable lubricating film between the mold and the workpiece, prevent adhesion, and reduce deformation resistance and surface scratches.

Surface pretreatment: Before cold processing, the surface oxide film and impurities of the titanium blank must be removed by methods such as pickling (mixed acid of hydrofluoric acid and nitric acid, the formula is generally 2–5% HF + 15–20% HNO₃ + water) or sandblasting, to ensure the surface cleanliness and flatness of the blank, and avoid the impact of surface defects on processing quality.

Controlled deformation rate and deformation amount: The cold deformation rate should be moderate (generally, the strain rate is controlled at 0.001–0.1 s⁻¹). Too fast a deformation rate will cause the material to not have enough time for plastic flow, leading to cracking; too slow a rate will reduce production efficiency. At the same time, the single-pass deformation amount should be strictly controlled (for example, the single-pass reduction rate of cold rolling is generally 5–10%, and the single-pass bending angle is not more than 30°), and multiple passes of small deformation should be adopted with intermediate annealing to ensure the uniformity of deformation.

info-443-446info-443-444

info-443-444info-448-448

2. Hot Working of Commercially Pure Titanium

2.1 Processing Difficulty

The hot working of CP Ti has medium difficulty, and its core challenges are derived from the high-temperature characteristics of titanium, which are specifically reflected in:

Narrow hot working temperature range: The phase transition temperature of CP Ti is about 882°C (the HCP structure (α-phase) is transformed into body-centered cubic (BCC) structure (β-phase) above this temperature). The optimal hot working temperature range is generally 700–850°C (between room temperature and phase transition temperature, i.e., in the α-phase region). If the temperature is lower than 700°C, the material still has high deformation resistance and obvious work hardening; if the temperature exceeds 850°C (close to the phase transition temperature), the grain will grow rapidly, resulting in coarse grain structure of the workpiece, which reduces the mechanical properties (such as toughness and fatigue strength). In addition, if the temperature exceeds 882°C and enters the β-phase region, the grain will be seriously coarsened, and even brittle intergranular phases will be formed after cooling, which will significantly deteriorate the performance of the material.

High-temperature oxidation and pollution sensitivity: CP Ti has extremely strong chemical reactivity at high temperatures (above 400°C), and will react with oxygen, nitrogen, hydrogen, and other gases in the air to form brittle surface layers:

Oxidation: Forming a porous and brittle TiO₂ scale, which reduces the surface quality and mechanical properties of the workpiece;

Nitridation: Forming TiN hard and brittle phase, which makes the material brittle and prone to cracking during processing;

Hydrogen absorption: Forming TiH brittle phase, leading to hydrogen embrittlement of the material and reducing its toughness.

Low thermal conductivity and uneven temperature distribution: The thermal conductivity of CP Ti is only about 1/5 of that of steel and 1/3 of that of aluminum alloy. During hot processing, the heat transfer inside the material is slow, which is easy to cause uneven temperature distribution between the surface and the core of the workpiece, resulting in uneven deformation and internal stress, and even cracking or deformation of the workpiece.

2.2 Special Process Requirements

To ensure the quality of hot working, CP Ti must adopt the following special processes:

Precise temperature control: The heating temperature must be strictly controlled within the range of 700–850°C, and the temperature deviation should not exceed ±10°C. The heating equipment should use a precision-controlled electric furnace or vacuum furnace instead of open flame heating (to avoid local overheating or uneven heating). During processing, the temperature of the workpiece should be monitored in real time (using infrared temperature measurement or thermocouple). If the temperature drops below 700°C, the workpiece should be returned to the furnace for reheating to avoid processing in the low-temperature zone with high deformation resistance.

Protective atmosphere or surface coating: To prevent high-temperature oxidation and gas pollution, the following protective measures can be taken:

Vacuum heating: Heating the workpiece in a vacuum environment (vacuum degree ≥ 10⁻³ Pa) to completely isolate the air and avoid gas reaction;

Inert gas protection: Filling the heating furnace with high-purity argon or nitrogen (nitrogen is only suitable for low-temperature heating below 600°C to avoid nitridation) to form a protective atmosphere;

Surface anti-oxidation coating: Coating the surface of the workpiece with a special anti-oxidation coating (such as glass-based coating or boron-based coating) before heating, which can form a dense protective film at high temperatures to isolate oxygen and nitrogen.

Reasonable hot working process parameters: The hot deformation rate should be controlled at 0.1–10 s⁻¹ (the α-phase of CP Ti has better plasticity in this strain rate range). The single-pass deformation amount should be appropriately increased (generally 30–50%) to make full use of the high plasticity of the material at high temperatures and avoid multiple small deformations leading to grain coarsening. After hot processing, the workpiece should be cooled in time (air cooling or water cooling, depending on the grade and thickness of the material) to suppress grain growth and ensure fine-grained structure.

Post-processing heat treatment: After hot working, the workpiece needs to be subjected to stress relief annealing or recrystallization annealing to eliminate internal stress and refine grains. The annealing temperature is 600–700°C, and the holding time is determined according to the thickness of the workpiece (generally 1–3 hours). For workpieces with high performance requirements, double annealing (first heating to 750°C for holding, then cooling to 600°C for holding, and finally air cooling) can be adopted to further optimize the structure and properties.

3. Summary

In general, the cold working of commercially pure titanium is difficult due to high work hardening and low ductility, requiring intermediate annealing, high-performance lubrication, and precise deformation control; the hot working is mainly challenged by narrow temperature range and high-temperature oxidation, and must rely on precise temperature control, strict atmosphere protection, and reasonable post-processing heat treatment. Both cold and hot working of CP Ti cannot adopt conventional steel or aluminum alloy processing processes, and must be implemented with targeted special processes to ensure the processing quality and performance of the final product.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry