Oct 21, 2025 Leave a message

ASTM B622 UNS N06022 Low-Carbon Ni-Cr-Mo-W Seamless Pipe: Chemistry and Corrosion Duty

Alloy Identity and Specification Scope

ASTM B622 is the specification for seamless nickel and nickel-cobalt alloy pipe, and it covers the low-carbon nickel-chromium-molybdenum-tungsten grade UNS N06022, also known as DIN 2.4602. Pipe and tube to this specification are supplied in the solution annealed and descaled condition; the descaling step can be omitted when the fabrication atmosphere is properly controlled.

The standard deals with the seamless form in sizes up to 3.5 in. (88.9 mm) outside diameter, and it fixes minimum mechanical properties plus the chemical limits below. Pipe to the same alloy in welded form is covered by separate specifications, so the seamless designation must always be verified on the mill certificate.

Chemical Composition and the Role of Each Element

Element Nickel Chromium Molybdenum Tungsten Iron Cobalt Manganese Silicon Carbon Vanadium Phosphorus Sulfur
Content, % Balance 20.0 to 22.5 12.5 to 14.5 2.5 to 3.5 2.0 to 6.0 2.5 max 0.50 max 0.08 max 0.015 max 0.35 max 0.02 max 0.02 max

Chromium supports the passive film that defeats oxidizing media, while molybdenum and tungsten provide the resistance to reducing acids and to chloride pitting. The deliberately low carbon limit of 0.015 percent is what makes the grade attractive for welded systems: with so little carbon available, chromium carbide precipitation in the heat-affected zone is suppressed, so intergranular attack remains unlikely without a post-weld solution anneal.

Mechanical and Physical Properties

Property Value
Density 8.69 g/cm3
Melting point 1399 C (2550 F)
Tensile strength, min 690 MPa (100 ksi)
Yield strength, min 310 MPa (45 ksi)
Elongation, min 45 %
Typical anneal 1121 C (2050 F), followed by rapid cooling

The combination of high strength and 45 percent minimum elongation reflects a fully austenitic structure with no precipitation hardening. Cold working raises strength well above the annealed minimum, and the higher strength level can be delivered when the purchase order specifies a cold-worked condition.

Where temperature is concerned, the low-carbon grade should not be used continuously above about 677 C (1250 F). Above that threshold long-term microstructural instability and the risk of detrimental phase formation outweigh any strength advantage, so the service temperature must be checked as part of the design review.

Corrosion Performance in Aggressive Media

The grade was developed for duties where neither a straight stainless steel nor a simpler nickel alloy survives. Its distinguishing feature is simultaneous resistance to oxidizing and reducing conditions, which removes the need to guess the chemistry of the process stream.

Pitting and crevice corrosion: the molybdenum and tungsten additions, together with high chromium, deliver strong resistance in chloride-bearing water, brackish water and chlorinated process streams.

Stress corrosion cracking: the nickel-rich austenitic matrix resists chloride cracking that would destroy standard austenitic stainless steels at similar temperatures.

Mixed acid and high-temperature media: buffered solutions, active pharmaceutical ingredients, surfactant and detergent streams, cleaning products, and food process streams such as brine-based sauces and pastes are all within its normal working range.

Because the alloy relies on alloying rather than on a single passive element, attack tends to be uniform and predictable; crevice conditions and stagnant flow remain the two situations requiring active design attention.

Applications by Industry

Chemical processing: reactors, heat exchangers, columns, absorber towers and general piping in plants handling chlorides, mixed acids and oxidizing agents.

Water treatment: valves, pumps and piping exposed to chlorinated water and other corrosive treatment chemicals.

Pharmaceutical: process equipment and storage vessels that must resist corrosion without contaminating the product.

Oil and gas: pumps, valves and instrumentation lines in sour and chloride-rich environments.

Frequently Asked Questions

Q: What does the low-carbon designation of UNS N06022 actually deliver?
With carbon held to 0.015 percent maximum, chromium carbide precipitation in weld heat-affected zones is suppressed, so intergranular corrosion resistance is largely retained in the as-welded condition.

Q: What condition is the pipe supplied in?
The standard condition is solution annealed and descaled. Descaling may be unnecessary where the fabricating atmosphere is controlled to prevent oxidation.

Q: What is the upper temperature limit?
Continuous service above roughly 677 C (1250 F) is not recommended because prolonged exposure promotes detrimental phase formation in this low-carbon Ni-Cr-Mo-W grade.

Q: Can the alloy be cold worked to higher strength?
Yes. Cold working raises tensile and yield strength above the annealed minimums, and higher-strength product can be supplied when the purchase order specifies it.

Q: How does the seamless form differ from welded pipe of the same alloy?
Seamless pipe is covered by ASTM B622 for pipe and by companion specifications for tube, while welded product falls under separate standards. The two must not be interchanged without reviewing the applicable specification.

Q: Does it resist both oxidizing and reducing media?
Yes. High chromium addresses oxidizing conditions, while molybdenum and tungsten handle reducing conditions, which is why the grade is selected where the process chemistry varies.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry